Wallpapers are the most common today.finishing material. They are great for any setting. Manufacturers offer a variety of options for canvases, you can choose not only the ornament, but also the thickness of the coating, resistance to moisture, ultraviolet light. It is important to immediately decide on what basis they will be. For example, how to glue wallpaper onto plywood? Wallpapers today are leadingposition among the finishing materials for the walls. The problem is that the plywood can shine through the wallpaper canvas. Its surface is too smooth, so not every type of coating can be used for plywood walls. If you accurately observe all the features of gluing, then the work will be done qualitatively and quickly.
Errors in work: how to avoid them?
How to glue the wallpaper on the plywood qualitatively? To get started, it's worth checking out the error list: A scheme for removing bubbles from the wallpaper.
There are other problems, their causes are violationtechnology of gluing and preparation of walls. Therefore, it is important to follow all the advice and recommendations accurately, and carefully consider preparation. To properly solve the problem of how to glue the wallpaper on plywood, it is necessary to prepare: Tools for gluing wallpaper.
- wallpaper of the selected type;
- wallpaper special glue;
- putty;
- a metal spatula;
- a container for mixing glue;
- building mixer;
- roller for applying glue;
- sharp knife;
- building level;
- ruler and a simple pencil;
- rags;
- sandpaper.
Back to contents</a>
The process of gluing on plywood
To paste wallpaper on plywood, it is necessary inaccuracy of technology. It's not complicated, but there are some features that need to be remembered. Before starting work, inspect the surface of the plywood wall. Often it is required to use a grinder to remove all roughness and other defects that may prevent the thin wallpaper liner from adhering. After that, the tree is primed, enough 1-2 layers, each of which must dry out. Further, the plywood is covered with putty, it removes the difference between the plate and joints, places of fastening. This must be done, since after gluing all the joints will be noticeable, the surface will become ugly. You can not start wallpapering without this. If the wall is made of non-veneer resistant plywood, thenBefore paving wallpaper, plywood must be painted with alkyd enamel. It is necessary to immediately determine which plywood was used for wall sheathing. If it was normal, that is, unstable to moisture, then it is necessary to cover the surface of the plates with special alkyd enamel. This will create a protective moisture resistant film. For walls, a special facing plywood can be used, which has a smooth front surface. With such plywood, it is necessary to carefully remove all dust with a damp rag. Attention should be given to joints, since it is in them that the greatest amount of dust and debris is collected. After the plywood base has been treated, leave it to dry. The room is recommended to ventilate. You can not glue the wallpaper on plywood, if its base is wet. All joints between the plates and the places of fastening to the wall are processed. Therefore, experts advise that, apart from putty, use strips of thin paper for seams. It is necessary after filling the seams for fresh putty to lay thin strips of paper, then apply another layer of the composition. After drying, the surface is re-treated, again left to dry. After such preparation it is necessary to clean the wall so that it becomes smooth and even. Back to contents</a>
Wallpaper gluing
When the wall is prepared and dried, you canstart to glue the wallpaper on the plywood. The process itself is not difficult, it differs little from the usual painting of canvases on the walls. It is only necessary to consider what kind of wallpaper was chosen. For example, for some glues it is necessary to apply only on the wall, and for others - on the canvas and on the wall. All the conditions of use the manufacturer indicates on the wallpaper, so it remains only to pick up the glue and start work. The wallpaper on the plywood is glued as follows: Technology of gluing wallpaper in the room.
Attention during work should be given to that,how exactly will be drawn up corners and places above window, doorways. For corners, you can not use a single piece of fabric or do so that the joints of two adjacent panels converge directly in the corner. It is necessary to cut off a strip of wallpaper with a width of about 30-40 cm. It is glued first to one side, then gently applied to the other, straightened. Above the window, doorways, the scheme is another. It is necessary, during the general finishing, to leave the wall of the wall above them unfixed, after which remove the pieces of wallpaper in accordance with the drawing (if necessary) and cut them. Further, the gluing is carried out exactly as for the rest of the wall space. The question of how to paste wallpaper on plywood walls, is solved simply. It is necessary to take into account all the recommendations and advice. For work it is important to prepare the base of the walls, handle all the joints, the places of fixing the plywood. After that, the gluing is carried out according to the general rules. </ ul>