How to glue wallpaper on whitewash: the process of preparing whitewashed walls for wallpapering

Wallpaper is a fairly popular finishingmaterials, which is most often used for wall decoration. But when planning such work, an important issue is the possibility of using the existing base and its correct preparation for gluing. Wallpaper can be applied to walls made of different materials. This is not only drywall, but also brick, concrete and other types. How, and can this be done? Whitewashing is not an ideal option; careful preparation of the surface of the walls is necessary. Otherwise, the canvases will disappear, the work will be extremely ineffective. Wallpaper must be glued only on the smooth prepared surface of the walls.

How to prepare a wall with whitewashing before wallpapering?

The question of how to glue wallpaper on whitewash is not solvedso difficult. Attention is paid not to the process of gluing itself, but to preparatory work with the wall. First, the surface is inspected, if necessary, repairs are performed. This concerns the sealing of cracks, the removal of traces of mold and other defects. Scheme of priming the wall. Then it is necessary to apply a layer of special primer to the surface. For these purposes, special acrylic compounds are used. They penetrate deeply into the base, strengthen it before performing the finishing works. The primer should dry out, then a second layer of it is applied, it also dries. The third layer is applied with a special strengthening compound. Usually used wallpaper paste, it is enough to dilute it with water. If whitewashing is of poor quality, then it is better to completely remove it. To do this, the surface is wetted with warm water, with a metal spatula, all the coating is removed. This work is long, dirty, so it is recommended to do without it if possible. Back to contents</a>

What kind of glue for wallpaper?

Whitewashing as a basis for gluing wallpapersvery demanding. Attention must be paid not only to the preparation of the surface, but also to the choice of adhesive composition. The glue must be of high quality, provide a reliable, strong grip. Otherwise, the canvas will lag quickly, you will have to repair it or start the pasting again. You can not save on the adhesive, as this can cause damage to the surface, as well as when choosing the wrong mix. Attention should be given to what type of material for decoration will be used, what exactly are the requirements for it. In order for the wallpaper to hold tight, wallpaperAdhesive must be prepared strictly according to the instructions. Today, manufacturers offer different types of wallpaper for walls. This means that the solution must be chosen for a particular type of finish. The following options are suitable:

For standard paper coatings, any universal quality adhesive is used. There are many options, there are no problems with the purchase.

If heavy coatings are required,including non-woven, vinyl, natural fabric, then you need to use special solutions designed for a particular type of coating. For non-woven and vinyl materials it is recommended to purchase a composition with PVA base, for others, solutions based on methylcellulose are excellent. These are water-resistant compounds, they are of excellent quality, often used when the wall is whitewashed.

For work it is necessary to use:

• wallpaper of the selected type;
• glutinous composition;
• rollers and brushes;
• a knife with replaceable blades;
• pencil and ruler for marking.

Back to contents</a>

The process of wallpaper gluing

After the preparation of the walls is finished, you can start gluing the surface with wallpaper. Such work is not too complicated, it is conducted in several stages: The scheme of wallpaper gluing.

First you need to vacate the room from allstrangers, unpack the wallpaper. Cutting is carried out for each individual canvas, at the same time it is necessary to remember about cutting for combining the pattern, about allowances for seams, if the type of wallpaper it requires. For cutting, you need to use a special knife with replaceable blades, put an unnecessary piece of drywall under the sheet, so as not to damage the floor covering.

It is required to prepare the glue that is selected independing on the type of cloth. Wallpapering on the whitewash layer will be of high quality if the linen is thoroughly impregnated with a glue composition. All excess glue during application should be cleaned immediately. When the glue dries, it will be problematic to remove it. It is done by a clean rag.

On wallpaper, the adhesive is applied with a roller or a wide brush. If the kind of cloths this requires, then the glue must be additionally applied to the wall surface. Do this immediately before the sheet of material is glued.

The material is doubled, after itglue, starting from the top edge, diligently straightening all the wrinkles and removing bubbles. It is best to work together. One will carry out the finishing, and the second will submit new cloths, hold them in the necessary position below. To spread the canvas, you must use special soft rollers or a piece of clean rags. Movements should be from the center to the edges.

Non-woven wallpaper is stuck a little differently. The adhesive layer is applied to the wall, it is not necessary to impregnate the web with the composition. If you do not comply with this condition, the material immediately after gluing will fall off, the work done will be absolutely useless. The weight of non-woven fabrics is considerable, so a special adhesive is used.

Back to contents</a>

Where to start and what to finish?

Procedure for wallpaper gluing. The process starts from the window opening, all corners are pasted together. This work is difficult, patience and attentiveness are required here. For internal corners, you must first attach a small part on one side to the wall, straighten it. After that, you can glue the second part already on the adjacent wall, gradually smoothing the wallpaper from the corner to the joint. For external corners, the process is almost the same. Sites above the window, doorways, behind the batteries and niches are pasted in the last place. In this case, wallpapering on the whitewash is carried out in small pieces, which remained after the design of the main space of the walls. In this case, the drawing should be treated with caution. If there is a possibility, then not one whole canvas and a small strip of it are applied, but 2 parts of the finishing material, cut equally. When all walls are ready, leave room to dry the glue. Time depends on the type of material and glue, but it is important that the temperature is maintained room, drafts are not allowed. Whitewashing for walls is rarely used, but this option is not excluded. When it is planned to finish the surface of the walls, it is necessary to take into account what exactly can be used for such a foundation. You can stick wallpapers to whitewash, although this is not the best option. It is worth paying close attention to the preparation of the wall.

Comments

Comments