For the decoration of the walls used a variety ofmaterials, which differ in attractive appearance and good performance characteristics. The MDF panels, which are perfectly suited to the modern style, can be separately noted. These materials can imitate various surfaces, while the MDF panel decoration is simple. MDF paneling is popular with MDF panelssimplicity of installation of the material and relatively low cost of the necessary materials. The paneling of MDF panels requires the presence of such tools and materials:
- building level;
- perforator;
- Screwdriver;
- drill, set of drills, crowns to it;
- MDF panels of the selected type;
- wooden slats;
- self-tapping screws, galvanized nails, dowels;
- a metal ruler, a simple pencil;
- heater.
Edging of the battens
Coloring of MDF panels. When it is planned to trim the walls of MDF panels, it is necessary to pre-prepare the crate. This is a frame made of wooden slats, to which the finish will be mounted. To trim the walls of MDF panels, you need to prepare the bars for the frame. They are pre-coated with special antiseptics, flame retardants to protect the structure from rotting, the negative effects of an open flame. For some time the tree perfectly resists ignition, i.e. there is a possibility to extinguish a possible fire. Wall finishing begins with the installation of vertical rails, they are fastened to the wall surface by dowels. First, the marking is done, the step of the laths for the battens is approximately the width of one MDF panel, typically a standard distance of 60 cm is observed. If the wall is wooden or brick, then self-tapping screws are used as fasteners. Back to contents</a>
Wiring
On the installation of wiring should think in advance. After finishing, planning to conduct electrical wiring will be unreasonable. Panels will either have to be cut or removed, but all this is extra time and a waste of financial resources. Why complicate your work, when you can do it all at once? When finishing the walls of MDF is still planned, you must immediately select the cable, calculate its number. The cross section is best taken for the installed electrical appliances. It is determined by the number of points, the expected load and other parameters. The length of the cable is taken in such a way that the fastening of the wiring is not end-to-end, it is necessary to add about 20% additionally. The wall will be prepared this way: The scheme of installation of MDF panels.
When the wiring is complete,begin to insulate. For this, mineral wool or polystyrene is used, the slabs between the batten rails are laid. The heat insulator should be laid as tightly as possible, leaving no gaps. Otherwise, the decoration of the walls will not be so qualitative, there will be drafts, points of heat loss. Back to contents</a>
Panel mounting
The decoration of the walls of the MDF is not used todayoften as wallpaper or plaster. If quick and easy installation is required, then preference can be given to this coating. In comparison with plastic panels, the MDF finish seems a little more complicated, but if you pay attention to the installation features, take into account all the recommendations, then the work will be qualitative and easy. After all the preparatory work is completed, the MDF panels themselves can be directly attached. At facing the following actions are performed: Step-by-step installation of MDF panels.
Back to contents</a>
Facing works
Paneling of walls with panels is carried out in this order:
When facing surfaces, you must observe certain features:
Back to contents</a> How to disguise scratches? The last step after finishing the walls with panels is the work on the slopes. MDF panels are also used here, they are fixed on the frame. If the finish of walls is scratched, then there is no need to panic, such a problem is easily solved (if, of course, the damage is not too strong). For this purpose, there are special furniture mastics, selected for the color of the material. They are carefully applied to the panel, using a rubber spatula, pressed into a scratch, and then rubbed. After doing this work and drying the mastic, an even coating is formed, the defect is no longer visible. Finishing the walls with MDF panels is an excellent variant of decorating the surface, imitating natural wood. Panels are easily attached to the surface of the wall, using the usual crate. No special experience is required, almost anyone can cope with such work. </ ul>