How to make gypsum board walls by your own hands: installation methods

Drywall is the most popularmaterial for facing different surfaces. But the most demanded application of drywall is in the formation of walls. The main reason for popularity is the extreme simplicity in installation and subsequent operation of drywall. This is quite natural, because it is really unpretentious material. Gypsum cardboard is a very popular material for wall sheathing, as it is easy to install and use.

Drywall and ways of its installation

GKL represents exactly that material,which allows you to quickly bring any room into the proper form. Installation of drywall with their own hands will not only hide some of the defects and unevenness of the walls, but also significantly insulate them, and also make an excellent soundproofing. Successful installation of drywall with their own hands is impossible without knowing some of the nuances of its application: Scheme sheet drywall.

The material can be applied to the wall by the most common method, that is, to build a frame of metal and simply attach the drywall to it with the help of screws.

The application of the product to the wall can also be done by gluing. And this option is no worse than the previous one, and some seem even easier.

If we consider the application of material on the wall,then you should pay attention to the products from the German manufacturer, which is called Knauf. Practice shows that it is used by almost 70% of Russians, which means that the company is proven and, most importantly, reliable. In any case, there were no serious complaints about this brand yet. Back to contents</a>

How to attach drywall to the wall

If you want to do plasterboard applicationon the wall, that is, it makes sense to get acquainted with a special instruction that will most accurately tell you how to act in this situation. Before you trim the wall with this material, you need to carefully determine the type of drywall. After all, a lot depends on this choice, in particular, the appearance of the finished walls and their characteristics. A typical consumer for wall finishing can take advantage of the following product types: General scheme of fixing drywall on the walls.

Standard sheets, which are called GKL. It is advisable to use them in ordinary residential premises, where it is quite dry. Such material allows to carry out complex wall finishing.

The material is extremely resistant to moisture. As a rule, it is used in places with high humidity, although it can be installed in ordinary buildings, where sometimes humidity rises.

Fireproof material. It should only be used in places where there is an increased fire hazard. Basically, they get rid of the walls in various enterprises.

Back to contents</a>

The use of metal profiles for wall decoration

In most cases, a wall of plasterboardit is advisable to perform from ready-made profiles. They are great solutions for trouble-free installation of drywall. All that is required from the consumer is to purchase such material and fix it on the wall. Especially popular are these products when forming the septum. As practice shows, in retail outlets it is possible to find already galvanized profiles of such a plan, which are made with the use of tape made of steel of small thickness. In particular, from this type of profiles a solid frame of material is subsequently formed, which is very easy to install. The skeleton itself is a so-called powerful base on which plasterboard is attached. Back to contents</a>

Facing without the use of a carcass

Scheme for assembling gypsum board joints. This kind of wall cladding is more common than the previous one, because it is less expensive. After all, the purchase of special profiles, from which the frame is formed, takes a lot of money, which can not be said about the simple fixing of drywall. And this kind of method can not be called very difficult. It should be noted that it is recommended to do this kind of work exactly at the moment when the final finishing of the room is done. After all, the installation of a material without a framework implies some technical aspects, which are best performed when unfinished works on finishing the interior space. Plus, the installation of the product in this way, it makes sense to start in the winter when the heating is on, so that the room is constantly maintained the same temperature. Naturally, the dimensions of the plasterboard should correspond to the size of the walls, on which plasterboard sheets will be installed. That's why you need to carefully measure the room before you begin its finish. Back to contents</a>

Preparation of walls and materials for facing

The success of such an enterprise largely depends on how the preparation for the work will be carried out. In itself, it is not very complicated, but you still need to know some features. Scheme alignment gypsum wall joints.

To begin with, determine the angle of curvature of the walls, which will most accurately tell you which type of cladding is best used.

Apply a special marking on the floor that touches the cladding, in particular, determine how the material should be placed in relation to the walls in the room.

Move the markings from the floor to the walls and ceiling, of course, using a special tool - a plumb line.

The surface of the wall that will be exposedfacing, must be carefully cleaned from various contaminants and obvious unevenness, which strongly protrude and will interfere with the installation of plasterboard. After the above manipulations, the wall should be thoroughly dried.

In order to properly primed the walls, you need to wait for them to dry completely and, accordingly, use specific substances, because, as is known, for each material there are their own mixtures.

Take care of the openings for the sockets andswitches in advance, cutting out special holes in them. In addition, you need to think about fixing the curtains and in appropriate places to handle the material with glue for greater stability.

After the plasterboard has been installed, all the existing gaps should be carefully treated with a special sealant that will secure and hide them.

In those places where the sheets of material will adhere to the corners of the walls, you must first get rid of chamfers for the convenience of further putty, which in any case will be needed.

It should be noted that if in the future you need to pasted sheets with wallpaper or painted, then you need to putty all the absolutely stuff, and not just joints and holes.

Back to contents</a>

Advantages and disadvantages of frameless gypsum board installation

Despite the fact that this kind of cladding is extremely popular, it also has its advantages and disadvantages. Pros and cons of wall finishing with plasterboard. Its main advantage lies in the low cost of the work. Considering the fact that you will only have to spend money on the purchased material and subsequent substances, which will not be so many, this method can be called really economical. If we consider fastening with the use of a frame, then there will need to be spent heavily on the profiles themselves to form the basis, which cost quite a lot, and even add all of the above costs. It should be noted and the fact that the frameless installation implies that the client can do it on his own and there is no need to order a special team for this purpose. Another undeniable advantage is the possibility of forming an ideally flat wall surface, which can not be said about the skeleton method, which does not allow, as they say, feel the wall. If it is required to apply the drywall already on the surface, then in this case all the roughness of the material is easily seen, which makes them very easy to eliminate. Naturally, we can not fail to note the speed of the work, which can not be said about the wireframe method, where it is necessary to first form the base, and then fix it with the help of special materials. One can not help but mention the simplicity of cleaning after carrying out all the above works. Speaking about the shortcomings, I want to note the fact that such a method will not allow to form a qualitative wall warming, as in the case with the wireframe version, and also it will not allow to hide some elements of communications from prying eyes. Although these shortcomings are more than offset by all the merits of the material.

Comments

Comments