Many people face the problem on a daily basisoverdried indoor air. This has an adverse effect on the body. Performance will decrease and a feeling of constant fatigue will appear. If funds allow, you can purchase special equipment to maintain the optimal temperature. But not everyone can spend money on such a purchase. How to make an air conditioner with your own hands will be discussed below.
Store-bought air conditioners are expensive, so you can make them yourself, and their quality will be no worse than store-bought ones.
Basic requirements for work
The system that controls the temperature in the room varies in its operating principle. It can be:
- evaporative;
- compressor.
To make the first type of unit yourself, you don’t need toit will be necessary to spend a large sum of money. The device works as follows: heat affects the moisture, due to which it evaporates and provides a normal climatic level.
Homemade air conditioner diagram.The first method is to use wet towels. It was used long before automatic air conditioners appeared. To achieve the desired effect, the fabric was generously soaked in liquid, after which all heating items were covered. The second method is to use a fan and water. For this method, you will need a fan in the house. Also prepare:
- a bottle with a wide mouth filled with water;
- cut fabric (better terry);
- fastening (use of metal wire is permissible);
- body.
If your house has wooden window frames, thenin the window, fix the canvas. One edge should be in a container with water. Then direct the air flow from the device towards the window. Monitor the level of moisture evaporation. Periodically top up the liquid. This option is suitable for those who do not like increased noise. The third model is made of plastic vouchers. To make the structure, you will need:
- fan;
- bottles of ice.
Air conditioner operation diagram.Fill the container with water, then place it in the freezer. Wait for it to solidify. After that, place them near the air flow. Keep some distance between them - no more than 5 cm. As soon as the ice melts, the bottle needs to be replaced. For the fourth type, you will need a copper tube and a rubber hose. Attach the tube to the fan frame. One end is connected to the hose, which is then attached to the cold water tap. The other end is discharged into the drain through the hose. By turning on the tap, you start the flow operation of the system. You can make an air conditioner with your own hands using the fifth method. You will need to prepare:
- ice;
- USB cable;
- a few screws;
- capacity (it can be plastic or tin);
- CD;
- cooler for computer.
Return to Contents</a>
Practical recommendations for work
So, you put pieces of frozen on the diskliquid. Then use screws to attach it to the center of the container. Make holes in the container at the bottom and around the perimeter of the CD. The first act as an air duct, the second allow melt water to drain. Attach a cable to the cooler and mount it on the top of the container. To start the design, insert the USB into the system unit or connect it to a laptop.
How a homemade air conditioner worksair heating and ventilation system of a house or cottage. For the sixth type of air conditioner, you will need an air purifier used in cars. You also cannot do without a ventilation device and a hose. To make the case, you can use improvised means. Surely, you have something suitable in your house. For example, a filter can be easily replaced with a mosquito net. But before installing it, you need to fold it several times. Fill the air purifier tank with liquid after all the parts are connected to each other. The principle by which the homemade device operates is the path taken by the air flow through the water barrier. During the passage, it cools down and exits through the filter. Connect the unit to the network and start operating. How to make a spray-type air conditioner with your own hands? For assembly you will need:
- container with water;
- spray;
- air duct;
- ventilation device.
Install an air duct on the filled vessel.Place a sprayer in the inner chamber. It should have a regulator that will control the flow of moisture. By starting the ventilation equipment, you activate the system. For those who have an old refrigerator gathering dust in their home, this advice will do. Place the freezer in the window. Insulate the cracks and holes in advance. The chamber should be installed with its front part facing the room. This way, the radiator will remain outside. To prevent the cold from accumulating in one place, you can make several holes with a drill on the side of the freezer. Another way to make a homemade air conditioner from a travel refrigerator. The latter is used as the basis of the system. You will also need a submersible pump and a radiator. A radiator is mounted in a portable refrigerator. To prevent it from moving around the body, use silicone glue. Connect the pump from below. It is permissible to use an aquarium pump. All wires should be on the outside. Cut a square on the inside of the lid, and two small circles on the outside. Insert small fans into them. After that, connect the wiring. To ensure silent operation of the device, attach a hose to the radiator outlet. Return to Contents</a>
Additional points
Another way is related to the usecar radiator. It is installed in the case of an old TV. A mandatory condition is the removal of all electrical components and a picture tube. It is in its place that the radiator is attached. A ventilation unit is attached at the back. The performance of the device depends on the strength of the air flow. A homemade air conditioner can be made from a minimum number of improvised means. Such a device will save money and provide a sufficient level of comfort in the hot season. Whichever of the options listed below you choose, do not forget about safety. Check how well the wires are working if their use is mandatory. Do not let moisture particles get on them. Do not forget about children, who may be attracted by the rotating blades of the fan.</ ul>
